Bullfrog Hot Tub-New Owners Page

Bullfrog Hot Tub

WHAT YOU NEED TO KNOW BEFORE DELIVERY

Hot Tub Checklist

OWNERS MANUALS

Hot Tub Owner's Manuals

Click on the Link Below for the Owners Manual

Bullfrog X, A, R, STIL, and M

PRE-DELIVERY INFORMATION

hot tub delivery

Bullfrog has prepared their ownPre Delivery Guide. May include information I have not included in any of my other posts.

ELECTRICAL INFORMATION

Hot Tub Electric

Be sure you check with your city or town for the most up-to-date information before attempting to do your own electric installation.

New York Hot Tub Code

Caution be sure that you have the correct Make, Model, and Model Year when referencing information on this page. The information on this page may be dated. Manufacturers do change wiring on their products as features change.

Need an Electrician. I recommend

Dwight Knox at D & D Electric. Office 585-624-3868. Cell 585-729-0684. I have referred Dwight for over 15 years and his company wired my personal hot tub at home.

Upstate New York Websites (permit information)

WIRING INSTRUCTIONS

Click on the Link Below for wiring information or a video that shows the bottom of the tub.

Bullfrog X, A, R, STIL, and M

Bullfrog Electric Chase Way Video

HOT TUBS USING @EASE SYSTEM

bullfrog @ease

Startup and Refilling

Before turning on the power fill your hot tub through the filter compartment to prevent an airlock. If possible remove the standpipe the filter sits on and put the hose down inside of it. If you do get an airlock you can watch the video on my post. I Just Got my Hot Tub, and I am having Problems

Anytime chemicals are added, run your jets for ten minutes with the cover open. Chemicals are best added in or near the filter compartment and when the water is 65 degrees or more.

Once the tub is powered on check your water balance with test strips to make sure your pH (7.2-7.8), Alkalinity (80-120), and water hardness (150-250) are in the proper range and adjust accordingly. Using granular chlorine establish a level of 3-5 ppm to purify the water before using the @ease system. Note any regular test strip can read pH, alkalinity, hardness, and chlorine. Only the Frog @ease test strip can read the @ease chlorine.

After your Alkalinity, pH, and water hardness are balanced and you have established a chlorine level. After 12 hours or if your chlorine level has below 3ppm you can then add the Frog Jump Start. Insert the Mineral & Chlorine Packs into the holder located in your spa. Be sure to set dials on packs according to the manufacturer’s recommendations in the frog @ease Manual.

Weekly

Use Frog maintain or any standard Spa Oxidizing Shock Once or Twice a week (to eliminate soaps/oils) depending on your usage. Soaps and oils will cause cloudy and foamy water.

I recommend and use it myself. Natural Chemistry’s Spa Perfect is a more effective alternative to the oxidizing shock.

A Stain & Scale Product is recommended to prevent calcium build-up especially if your water is high in minerals.

Check your Alkalinity, pH & Chlorine using test your @ease strips. If you want to be in the ‘Ideal’ range, adjust accordingly. Remember the Frog @ease is a low chlorine system and only needs to be between .5-1.0 on the chlorine scale using the @ease test strip

Monthly

Hose off your filters from top to bottom once a month (more often depending on your usage)

If you have a Vinyl type spa cover. Use a Spa Cover vinyl cleaner and protector on the spa cover. Fabric Covers do not require any maintenance.

Change Frog @ease Chlorine Pack

Add Jump Frog Start.

Every Four Months

Drain and refill the spa using the above startup directions

Replace Spa Frog Mineral Cartridge

Thoroughly clean filters using a Filter Cleaner per directions on the bottle.

Yearly

Use Natural Chemistry’s Spa Purge or similar product. Follow the directions on the bottle.

After the chemical is done drain and refills the hot tub.

Bullfrog @ease Startup Video

@ease manual

Frog @ease Water Balance Guide

CHLORINE ONLY SYSTEM

hot tub

Startup and Refilling

Before turning on the power fill your hot tub through the filter compartment to prevent an airlock. If possible remove the standpipe the filter sits on and put the hose down inside of it. If you do get an airlock you can watch the video on my post. I Just Got my Hot Tub, and I am having Problems

Anytime chemicals are added, run your jets for ten minutes with the cover open. Chemicals are best added in or near the filter compartment and when the water is 65 degrees or more.

Once the tub is powered on, add a Stain and Scale Prevention product following the manufactures directions.

Check your water balance with test strips to make sure your pH (7.2-7.8) and Alkalinity (80-120) are in the proper range and adjust accordingly.

Insert a Frog Mineral Stick into Filter Compartment. Any brand of Mineral Stick will also work.

Add One Tablespoon of Granular Spa Chlorine for Small Tub, Two for larger Tubs.

When all of the levels on your test strip are in range you are ready for a Soak.

After Each Use

Add one teaspoon of Granular Spa Chlorine per person after each use.

If the spa has not been used for more than 5 days or more add one tablespoon of chlorine.

Weekly

Use a Spa Oxidizing Shock Once or Twice a week (to eliminate soaps/oils) depending on your usage. Soaps and oils will cause cloudy and foamy water.

I recommend and use it myself. Natural Chemistry’s Spa Perfect is a more effective alternative to the oxidizing shock.

A Stain & Scale Product is recommended to prevent calcium build-up especially if your water is high in minerals.

Check your Alkalinity, pH & Chlorine using test your strips. If you want to be in the ‘Ideal’ range, adjust accordingly.

Monthly

Hose off your filters from top to bottom once a month (more often depending on usage)

If you have a Vinyl type cover. Use a Spa Cover vinyl cleaner and protector on the spa cover. Fabric Covers do not require any maintenance.

Every Four Months

Drain and refill the spa using the above startup directions

Replace Spa Frog Mineral Cartridge

Thoroughly clean filters using a Filter Cleaner per directions on the bottle.

Yearly

Use Natural Chemistry’s Spa Purge, following the directions on the bottle.

Drain and refill the spa.

FOR ADDITIONAL HELP TRY SOME OF MY OTHER BLOG POSTS

You just got your new hot tub, and it’s not working

My Water is Cloudy and Foamy. How Can I Fix It

HAVE A QUESTION

Leave a Reply

Your email address will not be published.